SLEEVES, RINGS & CIRCLIPS

 


 


Cylinder Sleeves for 836, 849 & 900cc Bore Kits

Even though 836 big bore kits have been around for years, some people believe that the wall thickness is thin. So, many people install these sleeves to regain wall thickness. These sleeves will be needed when increasing bore sizes larger than 65mm (836cc) up to 67.5mm. Outside diam. is 2.916 inches (74mm) The bottom of the sleeve is tapered down 2.752 (69.9mm) to allow the sleeves to fit inside of the upper case without bore the upper case larger. Inside diameter is 2.522 (64.07mm)

These sleeves have been the choice of engine builders for decades because of their dense long lasting cast iron materials. Most machinists can hear the difference when boring the cylinders and feel the toughness/denseness when honing them.

World class, race proven, and a price that is impossible to beat.

Note: Sometimes the upper cases have casting flash or casting protrusions which will need to be removed.

Note: Cylinder block will need to be bored for these sleeves.

Cycle X cast iron sleeves are the best in the industry.

836-849-900-SLEEVES     $219.00     (set of 4)
CALL OR EMAIL TO ORDER



 

970, 1000 & Up Big Bore Sleeves
Best in the industry!
Sleeves for 970, 1000 and above. 69mm I.D., 74.5mm O.D.

These sleeves have been the choice of engine builders for decades because of their dense long lasting cast iron materials.

Most machinists can hear the difference when boring the cylinders and feel the toughness/denseness when honing them.

World class, race proven and a price that is impossible to beat.

Note: Cylinder block and upper case boring required.

Cycle X cast iron sleeves are the best in the industry.

# BIGBORE-SLEEVES     $219.00
CALL OR EMAIL TO ORDER

 

Wiseco and JE Piston Ring Sets (65mm, 836cc)
Total Seal 2nd Compression Rings

We are told all ring sets are held up on a boat off shore with no due date in sight.
Here are some 2559XC rings that fit Wiseco and JE 65mm (836cc) pistons.
These 2559XC ring sets combined with total seal 2nd compression rings are the combination that many high level engine builders use.
Note: If your Wiseco/JE pistons are super old, consult with Wiseco/JE for fitment questions.

ENP-014     $159.00  (per set)


 

Honda 750 Standard Ring Set

1969-1976. Change your rings while your motor is apart.

ENP-013     $99.95  (per set)
 

 

 

836cc Ring Set (Wiseco)

Replacement rings for your 836 kit.
Question: If we take our motor apart, can we use the rings again?  Answer: No

ENP-012     $159.95 (per set)
 

 

Piston Circlips

 #CIRCLIPS     $10.95     (Set of 8)

 


If you're in need of tech help, refer to our pistons tech tips page.

 

HOME

Refurbished

Machine Work & Services

Close Out

Honda Hot Rod Motors

Pistons

Gaskets

Git Kits

Cush Drives & Chain Wheels

Crankshafts & Connecting Rods

Valve Train

Transmissions

Camshafts

Honda CB750 F2 Parts

Engine Chains

Clutches

Cylinder Studs

Carb Systems

Wheels & Accessories

Polishing, Chroming, & Black Chroming

Miscellaneous Parts

Rocker Arms

Tech Tips

Apparel & Accessories

Cam Chain / Primary Chain Tensioner

A 3.99% customer service charge is applied to all phone orders.

If ordering via phone, please also provide the part # of any products you are interested in for faster and more accurate service.

If you encounter a (rare) broken button as you're trying to add parts to your cart (going to PayPal summary instead of your cart or not opening PayPal at all) or anything else of concern, please call us to report it. We'll try to have it fixed for your convenience within the next 5-10 minutes. Afterwards, refresh the page and try again.

It is the sole and exclusive responsibility of the purchaser to determine the suitability of any part, product or work for his or her use.
The purchaser shall assume all legal, personal injury risk and liability and all other obligations, duties and risks therewith.
There is no warranty on High Performance products.

Click to go back to our Pistons Page

Cycle X Global Headquarters

6246 US Hwy 51 South

Hazelhurst, WI 54531

Phone: 715-356-7346

Email: hotrodcyclex@gmail.com